Electrical Technology Program Costs and Supply List
Cost Sheet 2020-2021.
| Costs per semester | full-time* | part-time* |
|---|---|---|
| Tuition/Fees (Kansas Resident) | $2280 | $1140 |
| Tuition/Fees (Contiguous Mo./Okla. Counties)** | $2520 | $1260 |
| Tuition/Fees (Non-Resident) | $3456 | $1728 |
| Additional Costs | ||
| Shop Fee*** | $400 | $200 |
| Tools (estimated) | $775 | $775 |
| Textbooks (estimated) | $450 | $450 |
*Full-time is based on 24 credit hours, part-time is based on 12 credit hours.
**Contiguous Missouri and Oklahoma counties:
Oklahoma counties include: Nowata, Washington, Ottawa, Craig, Osage and Rogers.
Missouri counties include: McDonald, Newton, Jasper, Barton and Vernon.
***Shop fee covers materials, supplies and safety glasses used in the classroom. All students are required to wear safety glasses, and attire appropriate for working conditions.
Quality of the tools is up to the student; therefore the price would vary with quality. All personal tools should be permanently inscribed with the student’s name.
Texts may be purchased at the College Book Store. Used ones may be available. Phone number is 620-252-7555.
Textbook List
Fall
Understanding the Nat. Elect. Code, Vol.1&2, 2014 Edition by Mike Holt Publications.
Electrical Wiring Residential, 17th Edition by Mullin/Simmons Delmar 2014 Edition.
AC/DC Circuits I Mike Holt Basic Electrical Theory 3rd Edition.
Electricity & Controls for HVAC Herman/Sparkman Delmar.
Spring
Electricity & Electronics, 10th edition, by Gerrish, Dugger, Roberts, Goodheart-Wilcox Co. Pub.
Understanding Motor Controls, by Stephen Herman Thomson/Delmar Publishers.
Electrical Commercial Wiring, 15th Edition Mullin Delmar.
Technicians Guide to Programmable Controls, 6th Edition Richard A Cox/Terry Borden Delmar.
Fall/Spring
NEC 2014 Electrical Code Book.
Tool List (Updated Fall 2024)
- Hard Hat (Electrical Rated)
- Claw Hammer
- 50 Ft Fish Tape
- Tool Pouch (With Belt) (Medium & Small) (Snap on Accepted)
- Allen Wrench’s (Metric & Standard)
- Nut Drivers (Standard)
- Screwdriver Set (Magnetized Optional)
- Insulated Screwdriver Set
- 10 inch Crescent Wrench (Optional Insulated)
- Romex Strippers
- Wire Strippers
- Crimpers
- GFCI Tester
- Non-Contact Voltage Tester
- Multimeter (600V or 1000V Range)
- Amp Clamp Meter (600V or 1000V Range)
- Side Cutters
- Channel Locks (Size 10)
- NM Cutters
- Precision Screwdriver Set (14-1 Tool Acceptable)
- 25-35 Ft Tape Measure
- Torpedo Level (Magnetic Optional, but Preferred)
- ½ EMT Pipe Bender
- ¾ EMT Pipe Bender
- Flashlight/Headlamp (Battery Operated is fine) (Optional With Head strap)
- Conduit Reamer
- Hacksaw
- Tool Bag (Tool Backpack or Carrier is Accepted)
- Lineman Pliers (9 inch)
- Needle Nose Pliers (8 inch)
- Box Knife (Foldable)
- Jab Hole Saw (Foldable)
Optional Tools
- Safety Glasses (Optional) (Class Supplies Basic Pair)
- Drill (Optional)
- Drill Attachments (Optional) (Nut Drivers, Drill bits, Screw bits)
- Gloves (Optional) (Electrical Rated)
- Socket Set (Optional)
- Wrench Set (Optional) (Box End, Ratcheting Accepted)
- Ugly’s Book (Optional 2023)
Tools Are Subject to Change.
Program Offers Tool Kit, Contact Dora Morris in the Tech Office for more information.
Graduation Fee
Students completing the program will have a fee of $45.00.
All of the above costs are subject to change. Please verify costs at time of enrollment.
All students that do not purchase school insurance must sign an insurance waiver before they will be allowed on the shop floor.
Cost of Attendance
View the Cost of Attendance Table for Coffeyville Community College here.